Polartec material note

What to Look for in a Water Resistant Fabric Supplier: A 6-Step Polartec Checklist

2026-08-27 · Lucia Bianchi

I rejected about 8% of fabric lots in our 2025 first deliveries for spec mismatches. Roughly 200 unique lots a year—I'd have to pull the audit summary to give you an exact count, but it's in that range.

This checklist is for teams sourcing polartec fleece fabric, polartec power stretch fabric, or any water resistant performance fabric through a distributor or contract manufacturer. It's relevant when the end product will see real outdoor use, not just casual wear. Six steps, in the order that catches the most problems first. That said, this comes from our experience with mid-weight knit fabrics; if you're building a hard-shell around a completely different construction, some details won't apply the same way.

Step 1: Verify the supplier is authorized to sell Polartec

Polartec sells through authorized distributors and converters. When someone says they can supply Polartec, ask for the authorization document. It should come from Polartec's regional sales office or appear on Polartec's official distributor list. Check the expiration date, too—authorization agreements lapse, and expired agreements are surprisingly common.

Why this step first? Because unauthorized "Polartec" is usually mill seconds, a previous customer's rejected lot, or a structurally similar copy. No amount of lab testing fixes a fabric that was never Polartec in the first place.

This is also the step that filters out a surprising number of traders. I've had sales reps tell me "we can get it from our partner in Portugal" without knowing the partner's name. A legitimate distributor has a current agreement and a named contact at Polartec.

I only started checking authorization documents after ignoring them once and eating a $22,000 redo. The price was 30% below everyone else. The "Polartec Power Stretch" turned out to be a knit that looked right in the hand but lost 11% stretch recovery after five washes.

Step 2: Confirm the exact product line and article number

Polartec is a fabric family, not one product. Power Stretch is a four-way stretch knit with a smooth face and brushed back, typically used in softshell panels and base layers. Power Stretch Pro adds a heavier face yarn for abrasion resistance. Thermal Pro is a high-loft fleece. Wind Pro integrates wind resistance into the knit. Alpha is breathable insulation. Power Air traps air pockets in a knit construction. NeoShell is a waterproof breathable membrane system. Delta is a breathable stretch knit for activewear.

Every product line has article numbers that map to a technical datasheet. Ask your supplier for the datasheet of the exact article you're quoting, then compare it with the physical sample they send—I mean, actually weigh it, measure it, stretch it. Don't just look at it.

The substitution I see most often is Power Stretch offered when the spec calls for Power Stretch Pro. They look nearly identical in the hand. The face yarn and recovery characteristics are different, though, and once the garment is cut and sewn, you're off-spec before you know it.

Step 3: Request lot-level third-party test reports

Here's the question that separates professional fabric suppliers from middlemen with a trademark license: "Do you have the test report for this production lot?"

Not the spec sheet from Polartec's website. The test report. From an independent lab. For the actual lot you're buying.

For polartec fleece and stretch fabrics, I look for: fabric weight (ASTM D3776 or ISO 3801), stretch and recovery (ASTM D3107 or ISO 20932), air permeability when wind resistance is claimed (ASTM D737), water resistance (AATCC 22 spray rating or ISO 811 hydrostatic head), and moisture vapor transmission rate when breathability matters (ASTM E96 or ISO 15496).

What I mean is that a lab report only has value if it's traceable to a lot number that matches what you're buying. A report without a lot number is evidence that some fabric met some standard at some point. That's a marketing document, not verification.

The most frustrating part of the process: even good suppliers push back here. They say "it's Polartec, it's already tested." You'd think a written request for a test report would be enough, but interpretation varies wildly. Now our purchase orders include a line: "Supplier required to submit lot-level test reports before shipment." No report, no PO.

Step 4: Run your own small-scale verification

Third-party reports are necessary but not sufficient. The report covers the sample the lab received, not the whole lot. So I run quick in-house checks on every new lot before we commit to production. I've used this protocol on lots going into 50,000-unit annual programs; it takes about a day once samples arrive.

First, the weight check. Cut a 10 cm × 10 cm swatch, weigh it, convert to gsm, and compare with the datasheet. Polartec knits typically tolerate about ±5%, but your garment costing depends on it being right.

Second, stretch recovery. Mark a 10 cm line, stretch to 50% extension, hold for 30 seconds, release, and measure after 30 seconds. A good Power Stretch fabric recovers to within 3-5% of the original length. If it's holding 10% or more, the knitting structure or elastane content is wrong.

Third, water beading. Drop water on the face at 45° and watch whether it beads and rolls off or spreads and wets out. Check at 30 seconds, 5 minutes, and 10 minutes. This tells you more about DWR quality than any brochure.

Finally, the wash test. Run 3 to 5 launderings per your care label spec, then re-check everything above. This is the step everyone skips. I caught a laminating peel issue on a Power Stretch lot this way in 2023—the supplier's lab report was real, but the lot had a different adhesive application. After the third wash, the layers separated visibly. So glad I ran that wash test. I almost skipped it to meet a production deadline, and that would have meant cutting 8,000 units of delaminating fabric.

Step 5: Check compliance certifications

For apparel sold in the US or EU, compliance documents are part of the fabric. On a Polartec order, I ask for:

  • OEKO-TEX Standard 100 — verifies testing for harmful substances. Confirm it covers the specific fabric class and that the certificate is current.
  • bluesign system partner status — Polartec's bluesign partnership is publicly documented, but coverage varies by article and production site. Ask whether the specific fabric is bluesign certified, not whether the brand is.
  • REACH compliance — required for EU market entry.
  • California Proposition 65 — relevant if the garments will be sold in California.

The question buyers don't ask often enough: are these certifications for this fabric article, produced at this factory? A brand-level bluesign membership is not the same as a product-level certification.

Step 6: Know the water resistance numbers before comparing prices

"Water resistant" means nothing without a test method and a numeric threshold. Two measurements carry most of the weight.

Hydrostatic head (ISO 811 or similar) measures the water pressure a fabric resists before leaking. In industry practice: 1,000–1,500 mm handles light rain; 3,000–5,000 mm covers moderate rain, which is where most "water resistant" garments sit; 10,000 mm is the commonly used waterproof threshold among outdoor brands; 20,000 mm+ is alpine-level confidence.

AATCC 22 spray rating measures the face fabric's ability to shed water droplets. Scores run 0 to 100, and new water resistant garments typically land around 80–90. The rating drops as the DWR deteriorates, which is why a wash test matters more than a fresh-sample test.

So when a supplier says their Polartec fabric is "waterproof," the only useful response is: what hydrostatic head value, measured by which method? If they can't answer, you're not comparing products. You're comparing preferences.

The same logic applies to NeoShell. If you're working with a waterproof fabric distributor who carries NeoShell, they should be able to provide both hydrostatic head and breathability numbers for the exact article code you're quoted. If they can't, go back to Step 3.

Common mistakes to avoid

Evaluating only the pre-production sample. The sample is often cut from a different lot than the bulk shipment. Verify lot numbers, and keep a sealed reference sample.

Treating fabric as the whole system. A water resistant garment fails at the seams first—especially with membrane fabrics like NeoShell. Confirm seam tape compatibility and test a taped seam construction, not just the flat fabric.

Confusing water resistant with waterproof. Different levels, different tests. If you need waterproof, spec the hydrostatic head minimum and the test method. Don't let terminology decide your product's ceiling.

Choosing solely on price per yard. The cheapest fabric that meets spec is the right answer. The fabric that's 20% cheaper but a 20% higher risk is how chargebacks happen.

Final note

Fabric sourcing decisions compound. A supplier with clean documentation means fewer surprises in production, fewer customer complaints, and a spec you can defend. A loosely documented supplier means you'll spend the season putting out fires.

Six steps: authorization check, article number, test reports, in-house verification, certifications, water resistance numbers. You don't need a lab to run all of it. You need to ask the right questions and verify the answers.

If you're considering a new water resistant fabric supplier, or setting up a performance fabric OEM arrangement for a new product line, run this checklist before you commit. It'll save you the preventable kind of pain, which is the only kind worth worrying about.